Table of Content
Measure 2 inches in from the edge and place a mark at the center of the board. Repeat this for the outside ends of both of the boards. Drill 5/8-inch-diameter holes through each of the boards at the marked positions. As mentioned above, the design pictured here differs slightly from Ben's design.
Add a final spray mark on the ground and then remove the stakes. Smear epoxy glue generously around the inside of all the 2-inch-deep holes in one of the boards. Insert an end of a 1-inch aluminum pipe into each of the holes.
Similar Posts
I cut the remaining 400mm in half using a 45 degree cut on my mitre saw. This gave me two pieces that I could brace either side of the leg. So I had my 25mm hole and a 25.4mm dowel to fit inside it.
Have an assistant ensure alignment and then place the wood block over the top of the board and hammer the open ends of the poles into the second set of holes. The fun part was getting the monkey bars lifted up and attached. A customer built this pull up and workout station using Kee Klamp pipe fittings and pipe. The entire structure is 10' tall and the width is 5' on all sides. This allows each of the "rungs" to be adjusted in distance from one another if needed.
DIY : How to Build Monkey Bars
You’ll need approximately 18 feet (5.5 m) total for your steps. While the concrete will feel dry to the touch within the hour, it takes longer for it to completely set. Level your posts immediately after pouring the concrete. Wear safety glasses and a dust mask when you’re mixing the concrete so you don’t get any of the powder if your nose or eyes. Check the specific instructions on the bags of concrete you’re using to see if there are any special mixing instructions.
I will be building this as well in ghe next few months but will be adding a small area for a baby swing to the side of it to go with the bigger kids playset/swing set. Do you find that the 21.5″ width of the monkey bars is a little restrictive? I’d like to go wider – like 30″, but I can’t find any monkey bar rungs that wide. You could even put another 4X4 support cemented into the ground to attach to it as well. Digging straight down with a shovel is difficult to say the least.
Where to Use Each Fitting:
Look for a set that has around 6–9 bars so you have enough to span the entire length. Aim to get monkey bars that are around 20 inches long so you have enough room to swing around and hold onto them. You can use any style as long as they mount to a flat surface.
While prefabricated sets are available for a price, creating a set of monkey bars requires only a few days and some tools and supplies to complete. Lumber, concrete mix and metal poles are available at most home improvement and hardware stores. Above, we've created a Sketchup modal of a set of monkey bars with a design similar to the one Ben built. We've removed the lower horizontal bar but have kept in the additional supports at the bottom to keep the structure safe and sturdy.
How Far Off The Ground Should Monkey Bars Be?
Between these 2 boards, screw in bars about 10 inches apart, which will be the rungs of the monkey bars. I bought 1 16 foot long pressure treated 4X4 and cut it in half because I didn’t need the posts to be the full height of the monkey bars. I used a paddle pit that was slightly smaller than the pipe, then slowly wallered it around until it was a tight squeeze for the pipe. I practiced on a scrap piece of 2X4 to ensure I would get it right. I did the 2nd flip bar at 42” for the little kids, however they tend to use the steps for the monkey bars to reach the taller one.
What’s more we distribute worldwide, so we can sell directly to you no matter where you live. To figure out the angle of the cut, I lay my ‘ladder’ on its side and placed one 1600mm length square against the end, creating a right angle . I then took a second 1600mm length and put one side on top of the first one with the other on top of the ladder frame, creating a triangle. Fit 2×4 braces to the stand, so you lock everything together tightly. Cut both ends of the braces at 45 degrees and then secure them into place with 2 1/2″ screws and glue.
Mix the concrete with water in a wheelbarrow or large bucket using a hoe or trowel. Slowly pour the concrete into the hole around the post until it’s filled to the top. Add the concrete to the remaining holes in the same way.
Check the remaining posts to ensure they’re all level as well. A timeless classic reinvented, we've designed the ultimate home Monkey Bars so that the entire family can benefit from the comfort of your own home. Our Monkey Bars for homes come in various shapes, sizes, and colours. Just add a splash of colour to your outdoor space, and roll up your sleeves for the best in creative, active play and fitness.
So we want to cover how and where to use each fitting, so you can build your own set of monkey bars. Yes, good mechanical practice would be to drill a pilot hole first, then put the lags in, which will avoid splitting the wood. The pilot hole should be a smaller diameter than the bolt, there are charts online to show the size of what your pilot hole should be for the size of bolt you are using. 1.5″ going through the 2X6 and 2.5″ going into the 4X4. You can continue building off of your monkey bars to add more fitness equipment. For example, you can attach a cargo net to the top of the run going down to the ground.
No comments:
Post a Comment